2 # Building, зона P5 Quan Shui, район Ганьцзинцзы, Далянь, Китай

Все Категории
EN
Позвонить

+86-411-39641370

Отправить письмо

vicente@konsond.com

Быстрорежущие стали

Главная>Наша продукция >Быстрорежущие стали

HSS round bar

Контакты

Характеристики
Быстрорежущие стали

High speed steel (or HSS) is often used in the manufacture of machine bits

High-speed tool steels are designed primarily for cutting tool applications. The term “high-speed” was used when these steels were first invented. The term refers to the fact that the steels could be used as cutting tools at high turning speeds on a lathe. In some cases, the turning speeds were so fast that the tools would heat to dull red color, which is about 1100°F (593°C). The ability to maintain the hardness required for cutting while at this temperature is a property known as red hardness or hot hardness, and it is the primary defining characteristic of high-speed steels.

High-speed steels exhibit high strength and hardness, but typically exhibit lower toughness than the cold work tool steels. Some, most notably M2 and powder metal M4, are used in cold work applications because of the strength and wear resistance which can be achieved.

To qualify as a high-speed steel, the chemical composition must meet certain minimum requirements, which are defined in the ASTM A600 Specification for High-Speed Tool Steels. The lowest alloy grades, M50 and M52 high-speed steels, are properly known as intermediate high-speed steels because of their lower alloy contents. The cobalt-bearing grades, such as M35 and M42, are known as super high-speed steels because they exhibit enhanced hot hardness.

The nominal chemical compositions of the common high-speed and intermediate high-speed tool steels are presented in weight percent below. Relative comparisons of the properties of the steels are presented in the chart on the reverse side. More specific information about the steels may be obtained from the individual data sheets. Grades with the DuraTech™ prefix are manufactured by powder metallurgy and provide very unique combinations of strength, toughness, and wear resistance. Several of the grades are also available in a resulfurized version. The sulfur addition improves the machinability of the steel in the annealed condition and the grindability in the hardened condition.

ASTMCMnSiCrWMoVCo
M10.820.250.403.751.558.501.15-
M20.850.250.304.156.004.801.85-
M2 EUR0.910.250.304.006.154.851.75-
M3-11.040.250.303.905.904.902.35-
M3-21.210.250.304.106.005.502,90-
M41.330.250.304.505.504.503.85-
Цена за тысячу показов M41.450.250.254.505.505.203.85-
M71.000.300.403.601.608.551.90-
M350.930.300.304.206.255.001.904.90
M421.080.300.453.851.509.501.208.00
CPM Rex 76/M481.550.200.404.0010.005.253.109.00
 M500.830.300.504.10-4.201.05-
M520.900.300.304.001.154.501.95-
CPMT151.600.300.304.2512.250.755.005.00
PM301.280.300.304.206.45.003.108.00

НаименованияРазмер (мм)ОбработкаУсловия доставки
Круглый стерженьДИАМ1.0 - 30Холодное волочение / Бесцентровое шлифованиеЯркий и отжиг
ДИАМ20 - 80ПилингЯркий и отжиг
ДИА 13-180ГорячекатаныйЧерная поверхность и отжиг
ДИАМ 70 - 400ГорячекатаныйЧерная поверхность и отжиг
Плоский барТ 3.0-20 ХВ 20-100ГорячекатаныйЧерная поверхность и отжиг
ЗаблокироватьТ 20-200 Х 300-800Горячекатаный и горячекованыйЧерная поверхность/Машина и отжиг
КатанкаДИАМ 5.5 - 13ГорячекатаныйЧерная поверхность и отжиг
ЛистыT1.0 - 2.5ХолоднокатаныеЧерная поверхность и отжиг
Т 2.5 - 8.0ГорячекатаныйЧерная поверхность и отжиг
Связаться с нами

Горячие категории